EC and pH for Water and Feed: targets, ppm factors and a routine.
Most feed problems start in the water. Here is what pH does to what the roots can reach, why EC is the number to trust, and why the same water can read two different ppm figures.
Bloom Grower Handbook · Chapter 07Key takeaways
- pH decides which nutrients the roots can use. Extension sources put most greenhouse substrates at 5.4 to 6.4.
- A ppm meter multiplies EC by a factor. Sources use different factors, so write EC.
- Test your source water first, then the mixed feed, the same way each time.
pH is the window, EC is the number
pH changes which nutrients roots can reach, even when plenty is in the water. EC measures how salty the solution is. Both belong in your log every time you mix.
| Where pH sits | What extension guidance says |
|---|---|
| Below the range | Iron and manganese can be over-available. Calcium and magnesium can be short.1,2,4 |
| 5.4–6.4 | Most greenhouse crops in soilless substrate.1 |
| Above the range | Iron, manganese, zinc and boron can be unavailable.2 |
Hydro growers: Oklahoma State puts the nutrient solution at pH 5 to 6 (usually 5.5) and the root zone at 6 to 6.5.3 Soil with 20%+ field soil sits higher: 6.2 to 6.5.4
One EC, two ppm numbers
| EC (mS/cm) | Penn State, ×640 (irrigation water) | NDSU table (natural waters) |
|---|---|---|
| 1.0 | 640 | 650 |
| 1.5 | 960 | 1,050 |
| 2.0 | 1,280 | 1,450 |
Estimated ppm (mg/L) from the same EC. Penn State uses a factor of about 640 for irrigation water.5 North Dakota State’s table shows the factor climbing from 0.5 to 0.82 as EC rises, for natural waters.6 Neither is a fertilizer-solution standard. Meters pick their own factor, so the same bucket reads differently.
EC is what the meter actually measures. ppm is EC multiplied by a factor someone picked. If you must quote ppm, say which factor.
Penn State flags raw irrigation water above 1.0 mS/cm EC for plugs and above 1.5 for other plants as a concern, before you add anything.5
A simple routine, and a unit decoder
- Test the source water. EC and pH of what comes out of the tap or RO, before any bottle goes in.
- Mix, then pH. Add the base and bottles per your chart, mix well, then adjust pH into your window.
- Read EC, log EC. Write down EC, pH, temperature and the week. Same sample method every time.7
- Calibrate the meter. Check against a calibration solution regularly, after a battery change or a drop.6
| Unit decoder | Equals |
|---|---|
| 1 mS/cm | 1 dS/m = 1 mmho/cm = 1,000 µS/cm |
| 0.5 mS/cm | 500 µS/cm. Mind the unit on the meter. |
| Hydro nutrient solution pH | 5–6, usually 5.53 |
| Hydro root-zone pH | 6–6.53 |
Soilless substrate
Peat and aged bark start at pH 3 to 4, so makers add lime to bring them into the window. Low substrate pH can push iron and manganese to toxic levels.1
Compare like with like
Extension advises collecting samples the same way each time and comparing your EC against targets from the same collection method.7 These are general greenhouse and hydroponic guidance. For Bloom additives, follow the chart for your medium; this chapter does not set rates.
What one grower said
“Notice it really lowers ph but not a problem at all for the results its showing.”
@greenmedsgarden Products named: Ooze. In the grower’s own words, from a DM. He noticed his feed pH dropped with Ooze. One grower’s observation: always measure and adjust your own pH.
Other crops: growing fruit, veg, peppers or ornamentals? Rates and the feed schedule are on the fruit and veg feed schedule page. This handbook prints no crop rates.
Honest check
- These ranges are general greenhouse and hydroponic extension guidance, not cannabis trial results and not Bloom targets.
- Neither ppm factor is a fertilizer-solution standard.
Sources
- Lindberg H, Owen WG (2018). Managing substrate pH of soilless substrates. Michigan State University Extension. canr.msu.edu
- Shober AL, Denny GC. Identifying nutrient deficiencies in ornamental plants. University of Delaware Cooperative Extension. udel.edu fact sheet
- Singh H, Dunn B. Electrical conductivity and pH guide for hydroponics. Oklahoma State University Extension. extension.okstate.edu
- UMass Extension Greenhouse Crops and Floriculture. Soil test report, commercial floriculture (nutrient levels and optimum pH). umass.edu fact sheet
- Rhea D, Canfield C, Snyder K, Swistock B (2025). Interpreting irrigation water tests. Penn State Extension. extension.psu.edu
- North Dakota State University Extension (WQ1923). Using electrical conductivity and total dissolved solids meters to field test water quality. ndsu.edu
- Getter K (2013). pH and EC issues still a problem in some greenhouses. Michigan State University Extension. canr.msu.edu
Go deeper
Rates for your medium, once your water is sorted.Nutrient calculator →
Mix by EC for your reservoir size.Ooze →
The bottle the grower above saw lower his feed pH.The Science →
The research behind how Bloom is built.
Questions growers ask
What pH should my nutrient solution be?
Why use EC instead of ppm?
What ppm factor should I use?
What is a good routine for mixing feed?
How do I convert EC units?
When is source water a problem before I add anything?
Questions on your grow? Talk to Nate.
Product images are renders. Stage and cover images are a mix of AI-generated illustrations and photos, used to show how things work, not results. This is general growing information for legal crops. Follow your local laws and the product label. Bloom products are plant nutrient additives. They are not pesticides and are not certified organic.
