Bloom Yellow Bottles

Grower Handbook · Chapter 07

EC and pH for Water and Feed: targets, ppm factors and a routine.

Most feed problems start in the water. Here is what pH does to what the roots can reach, why EC is the number to trust, and why the same water can read two different ppm figures.

US Edition · Free download · Sources kept
Dark soil with fine white roots, the Bloom Grower Handbook chapter on water, EC and pHBloom Grower Handbook · Chapter 07

Key takeaways

  • pH decides which nutrients the roots can use. Extension sources put most greenhouse substrates at 5.4 to 6.4.
  • A ppm meter multiplies EC by a factor. Sources use different factors, so write EC.
  • Test your source water first, then the mixed feed, the same way each time.

pH is the window, EC is the number

pH changes which nutrients roots can reach, even when plenty is in the water. EC measures how salty the solution is. Both belong in your log every time you mix.

Where pH sitsWhat extension guidance says
Below the rangeIron and manganese can be over-available. Calcium and magnesium can be short.1,2,4
5.4–6.4Most greenhouse crops in soilless substrate.1
Above the rangeIron, manganese, zinc and boron can be unavailable.2

Hydro growers: Oklahoma State puts the nutrient solution at pH 5 to 6 (usually 5.5) and the root zone at 6 to 6.5.3 Soil with 20%+ field soil sits higher: 6.2 to 6.5.4

One EC, two ppm numbers

EC (mS/cm)Penn State, ×640 (irrigation water)NDSU table (natural waters)
1.0640650
1.59601,050
2.01,2801,450

Estimated ppm (mg/L) from the same EC. Penn State uses a factor of about 640 for irrigation water.5 North Dakota State’s table shows the factor climbing from 0.5 to 0.82 as EC rises, for natural waters.6 Neither is a fertilizer-solution standard. Meters pick their own factor, so the same bucket reads differently.

So: write EC

EC is what the meter actually measures. ppm is EC multiplied by a factor someone picked. If you must quote ppm, say which factor.

Watch your source water

Penn State flags raw irrigation water above 1.0 mS/cm EC for plugs and above 1.5 for other plants as a concern, before you add anything.5

A simple routine, and a unit decoder

  1. Test the source water. EC and pH of what comes out of the tap or RO, before any bottle goes in.
  2. Mix, then pH. Add the base and bottles per your chart, mix well, then adjust pH into your window.
  3. Read EC, log EC. Write down EC, pH, temperature and the week. Same sample method every time.7
  4. Calibrate the meter. Check against a calibration solution regularly, after a battery change or a drop.6
Unit decoderEquals
1 mS/cm1 dS/m = 1 mmho/cm = 1,000 µS/cm
0.5 mS/cm500 µS/cm. Mind the unit on the meter.
Hydro nutrient solution pH5–6, usually 5.53
Hydro root-zone pH6–6.53

Soilless substrate

Peat and aged bark start at pH 3 to 4, so makers add lime to bring them into the window. Low substrate pH can push iron and manganese to toxic levels.1

Compare like with like

Extension advises collecting samples the same way each time and comparing your EC against targets from the same collection method.7 These are general greenhouse and hydroponic guidance. For Bloom additives, follow the chart for your medium; this chapter does not set rates.

What one grower said

“Notice it really lowers ph but not a problem at all for the results its showing.”

@greenmedsgarden Products named: Ooze. In the grower’s own words, from a DM. He noticed his feed pH dropped with Ooze. One grower’s observation: always measure and adjust your own pH.

Other crops: growing fruit, veg, peppers or ornamentals? Rates and the feed schedule are on the fruit and veg feed schedule page. This handbook prints no crop rates.

Honest check

  • These ranges are general greenhouse and hydroponic extension guidance, not cannabis trial results and not Bloom targets.
  • Neither ppm factor is a fertilizer-solution standard.

Sources

  1. Lindberg H, Owen WG (2018). Managing substrate pH of soilless substrates. Michigan State University Extension. canr.msu.edu
  2. Shober AL, Denny GC. Identifying nutrient deficiencies in ornamental plants. University of Delaware Cooperative Extension. udel.edu fact sheet
  3. Singh H, Dunn B. Electrical conductivity and pH guide for hydroponics. Oklahoma State University Extension. extension.okstate.edu
  4. UMass Extension Greenhouse Crops and Floriculture. Soil test report, commercial floriculture (nutrient levels and optimum pH). umass.edu fact sheet
  5. Rhea D, Canfield C, Snyder K, Swistock B (2025). Interpreting irrigation water tests. Penn State Extension. extension.psu.edu
  6. North Dakota State University Extension (WQ1923). Using electrical conductivity and total dissolved solids meters to field test water quality. ndsu.edu
  7. Getter K (2013). pH and EC issues still a problem in some greenhouses. Michigan State University Extension. canr.msu.edu

Go deeper

Questions growers ask

What pH should my nutrient solution be?
Extension sources put most greenhouse soilless substrates at 5.4 to 6.4. For hydroponics, Oklahoma State puts the nutrient solution at pH 5 to 6 (usually 5.5) and the root zone at 6 to 6.5.
Why use EC instead of ppm?
EC is what the meter actually measures. ppm is EC multiplied by a factor someone picked, and sources use different factors, so the same bucket can read two different ppm numbers.
What ppm factor should I use?
There is no single standard. Penn State uses about 640 for irrigation water, while North Dakota State’s table shows the factor climbing from 0.5 to 0.82 as EC rises for natural waters. If you must quote ppm, say which factor.
What is a good routine for mixing feed?
Test source water EC and pH, mix the base and bottles per your chart, adjust pH into your window, then read and log EC, pH, temperature and the week using the same sample method every time.
How do I convert EC units?
1 mS/cm equals 1 dS/m, 1 mmho/cm and 1,000 microsiemens per cm. So 0.5 mS/cm is 500 microsiemens per cm. Check the unit on your meter.
When is source water a problem before I add anything?
Penn State flags raw irrigation water above 1.0 mS/cm EC for plugs and above 1.5 for other plants as a concern.

Download the full Grower Handbook (PDF, US Letter)

Questions on your grow? Talk to Nate.

Product images are renders. Stage and cover images are a mix of AI-generated illustrations and photos, used to show how things work, not results. This is general growing information for legal crops. Follow your local laws and the product label. Bloom products are plant nutrient additives. They are not pesticides and are not certified organic.

New to Bloom? Your one-time 30% thank-you is waiting.One-time 30% for first-timersClaim my 30%