Bloom Yellow Bottles

Grower Handbook · Chapter 10

Cuttings and Clones: humidity, root-zone temperature and light.

A cutting has no roots, so it cannot drink. Everything about rooting is about keeping it hydrated until it can. Here is what extension research says about humidity, warmth and light, and where Roots fits.

US Edition · Free download · Sources kept
Dark soil with fine white roots, the Bloom Grower Handbook chapter on cuttings and clonesBloom Grower Handbook · Chapter 10

Key takeaways

  • Early on, very high humidity (VPD about 0.3 kPa) keeps cuttings hydrated. Ease off as roots form.
  • A root zone of 72 to 75°F (22 to 24°C) with air about 5°F (3°C) cooler favors roots over shoots.
  • Roots is the Bloom bottle for new roots. Rates are on the chart.

Keep it hydrated, then ease off

Early in propagation, VPD of 0.3 to 0.4 kPa is recommended (85 to 90% relative humidity at 23°C, about 73°F) so water loss is slow. As cuttings develop roots, raise the VPD to promote root development and uptake.1

Rooting stageRelative humidity
Early rooting (VPD about 0.3 kPa)85–95% (90 to 95% in one source)2
Once an initial root system forms60–75%3

Michigan State Extension, ornamental cuttings and plugs. Too high a humidity can mean less developed roots and more disease.3

Warm roots, cooler air, gentle light

72–75°F
root-zone temperature recommended, 22 to 24°C, with air about 3°C (about 5°F) cooler than the media.
Bottom heat is usually needed to reach it. Fahrenheit shown is arithmetic from the source.1
200 µmol
rough ceiling on light intensity in early rooting, rising as roots develop.
Favors root growth over shoot growth.2

Scope: these are ornamental cutting and plug guidelines. Cannabis clones are similar, but not the same plant, so treat the numbers as a starting point.

Where Roots fits

Roots is the Bloom bottle for new roots, cuttings and transplants. It is made from Durvillaea potatorum, southern bull kelp, with 0.075% humic acid from leonardite and 0.054% thiamine hydrochloride (vitamin B1) on the label. It goes in the water you give the cuttings and young plants; the feed chart gives the rate.

  1. Light, porous medium. Rooting slows in a heavy mix that holds a lot of water.2
  2. Humidity first, then ease off. High early, then lower as roots appear.1
  3. Warm roots. Bottom heat to 72 to 75°F; air a little cooler.1,2
  4. Feed once roots form. Extension suggests a light fertilizer, such as an occasional watering at 150 ppm nitrogen, once roots develop.2
Keep it clean

Sanitation matters when handling cuttings and in the rooting space. Cover bare soil to stop algae building up.2 Chapter 11 has more.

Test it

Cut matched tips from one mother. Root half with Roots in the water and half without. Same room, same medium, same dome. Photo them on the same days and count rooted tips.

What one grower said

“Soaked root riot plug in sea minerals and roots mix with some water.”

@bige Products named: Roots, Sea Minerals. In the grower’s own words, from a DM. He sowed seed in plugs rather than rooting cuttings, and the photo is from later in his run. One grower’s view, not a measured result.

Other crops: growing fruit, veg, peppers or ornamentals? Rates and the feed schedule are on the fruit and veg feed schedule page. This handbook prints no crop rates.

Honest check

  • The humidity, temperature and light numbers are ornamental extension guidance. Bloom has not published a controlled rooting trial.
  • Auxin rooting compounds appear in the same extension articles. We do not cover or recommend them here.

Sources

  1. Runkle E. Propagation pointers. Michigan State University Extension. canr.msu.edu
  2. Runkle E. Improve rooting of cuttings. Michigan State University Extension. canr.msu.edu
  3. Runkle E. Indoor propagation. Michigan State University Extension. canr.msu.edu
  4. Bloom facts: Roots label. °F figures are arithmetic from the °C values in the sources.

Go deeper

Questions growers ask

What humidity do cuttings need?
Extension recommends VPD of 0.3 to 0.4 kPa early (85 to 90% RH at 23°C), then 60 to 75% once an initial root system forms. These are ornamental cutting and plug guidelines.
What temperature should the root zone be?
22 to 24°C (72 to 75°F) with air about 3°C (5°F) cooler than the media favors root growth over shoot growth. Bottom heat is usually needed.
How much light do cuttings need?
Extension gives a rough ceiling near 200 µmol in early rooting, rising as roots develop.
When should I start feeding cuttings?
Extension suggests a light fertilizer, such as an occasional watering at 150 ppm nitrogen, once roots develop.
What is Roots?
Roots is the Bloom bottle for new roots, cuttings and transplants, made from southern bull kelp with 0.075% humic acid and 0.054% vitamin B1 on the label. The feed chart gives the rate.
Has Roots been trialed for rooting?
Bloom has not published a controlled rooting trial. The handbook suggests a side-by-side: root matched tips from one mother with and without Roots in the water, and count rooted tips.

Download the full Grower Handbook (PDF, US Letter)

Questions on your grow? Talk to Nate.

Product images are renders. Stage and cover images are a mix of AI-generated illustrations and photos, used to show how things work, not results. This is general growing information for legal crops. Follow your local laws and the product label. Bloom products are plant nutrient additives. They are not pesticides and are not certified organic.

New to Bloom? Your one-time 30% thank-you is waiting.One-time 30% for first-timersClaim my 30%